Corrosion monitoring

Flange Access fitting include solid or hollow plug in it carry the internal corrosion monitoring or injection device. The get entry to fitting is permanently connected to the vessel or pipe, and the provider valve and retriever are used to insert or cast off the various probes, corrosion coupons or injection system.
This corrosion tracking access gadget is the global trendy for excessive pressure get entry to fitting systems and equipment for “get right of entry to below pressure” up to 6,000 psi (41 Mpa) and 450° F (232° C).

Material A105 CS, or others
Standard ASME B31.3
Standard Temperature Standard Temperature Rating with Viton/Teflon Seals:
From -15° F (-26° C) Up To +400° F (+204°C)
Type Flange RF, Flange RJ

2″ Ladder Corrosion Coupon of various length and models for 2″ system corrosion monitoring, which are commonly used for oil and gas, upstream and downstream, chemical companies, etc.

1 Pcs Corrosion Coupon consists of:

  1. Corrosion Coupon (AISI 1018 or others)
  2. Standard nylon insulator
  3. Serial number
  4. VCI cover / bag
  5. Envelope bag, silica and plastic bag

Ladder strip coupon holders are designed to concurrently screen corrosion at numerous tiers in a system line. this is a technique hired in massive diameter pipelines (8” O.D. and morein which corrosion might not be uniform across the diameter of the pipe, or in structures wherein flow is stratified.

minimal length holder of 26 cm (10.25″) is needed to mount three pairs of coupons.

Specifications:

Material AISI 1018, ASTM A106 gr B, or others
Weight Below 50 gram, depend on the model, details will be listed on the envelope
Standard NACE RP-0775 and ASTM G-1
Dimension 2″ x 7/8″ x 1/8″
Reference Catalog Bcormon
CORROSION COUPON
CATALOG

A connection fitting with a solid plug or hollow plug, it carries the monitoring of internal corrosion or an injection device. The access fitting is permanently attached to the container or driver, and the service valve and the retriever are used to insert or remove the different probes, corrosion coupon or injection equipment.

Material 316L / SS, A105 CS, or others
Standard ASME B31.3
Standard Temperature Standard Temperature Rating with Viton/Teflon Seals:
From -15° F (-26° C) Up To +400° F (+204°C)
Type Fitting Flarweld, Sockedweld, Buttweld, NPT

3″ Retractable Scale Coupons for 1” retractable systems, which are commonly used for oil and gas, upstream and downstream, chemical companies, etc.

1 pcs scale coupon consists of:

  1. Scale coupon (AISI 1018 or others)
  2. Standard nylon insulator
  3. Serial number
  4. VCI cover / bag
  5. Envelope bag, silica and plastic bag

Specifications:

Material AISI 1018, ASTM A106 gr B, or others
Weight Below 50 gram, depend on the model, details will be listed on the envelope
Standard NACE RP-0775 and ASTM G-1
Dimension 3″ x 1/2″ x 1/16″
Reference Catalog Bcormon

3″ Scale Coupons for 2″ system Corrosion Monitoring, which are commonly used for oil and gas, upstream and downstream, chemical companies, etc.

1 pcs scale coupon consists of:

  1. Scale coupon (AISI 1018 or others)
  2. Standard nylon insulator
  3. Serial number
  4. VCI cover / bag
  5. Envelope bag, silica and plastic bag

Specifications:

Material AISI 1018, ASTM A106 gr B, or others
Weight Below 50 gram, depend on the model, details will be listed on the envelope
Standard NACE RP-0775 and ASTM G-1
Dimension 2-7/8″ x 7/8″ x 1/8″

3″ Strip Corrosion Coupons model for 2“ System Corrosion Monitoring,  which are commonly used for oil and gas, upstream and downstream, chemical companies, etc.

1 pcs corrosion coupon consists of:

  1. Corrosion coupon (AISI 1018 or others)
  2. Standard nylon insulator
  3. Serial number
  4. VCI cover / bag
  5. Envelope bag, silica and plastic bag

Specifications:

Material AISI 1018, ASTM A106 gr B, or others
Weight Below 50 gram union depend on the model, details will be listed on the envelope
Standard NACE RP-0775 and ASTM G-1
Dimension 2-7/8″ x 7/8″ x 1/8″
Reference Catalog Bcormon

3″ Retractable strip Corrosion Coupon for 1″ system corrosion monitoring which are commonly used for oil and gas, upstream and downstream, chemical companies, etc.

1 pcs corrosion coupon consists of:

  1. Corrosion coupon (AISI 1018 or others)
  2. Standard nylon insulator
  3. Serial number
  4. VCI cover / bag
  5. Envelope bag, silica and plastic bag

Specifications:

Material AISI 1018, ASTM A106 gr B, or others
Weight Below 50 gram, depend on the model, details will be listed on the envelope
Standard NACE RP-0775 and ASTM G-1
Dimension 3″ x 1/2″ x 1/16″
Reference Catalog Bcormon

The Retractable Strip Corrosion and Scale coupon   a comprehensive range of weight loss coupons and holders covering applications in oil & gas, refinery and processing, water treatment and general industry.

Corrosion Inhibitor is a water based corrosion inhibitor formulated.

It will effectively inhibit corrosion caused by H2S, CO2 salt water and other elements. Designed to provide good film persistency and is dispersible in fresh and brine water. Low points in the bottom of flow lines where water has collected are protected because of the solubility of the product.

CHARATERISTICS:
Appearance Clear Liquid
Color Light Brown
Specific Gravity @ 25°C 0.95 – 0.99
pH 7 ~ 9
Solubility Water soluble, oil dispersible

APPLICATION:
A rule-of-thumb dosage rate is 10 – 20 ppm based on water production. This should be varied in accordance with the severity of the problem. Frequency and method of application vary over a wide range, depending upon individual characteristics.

STORAGE AND HANDLING:
Corrosion Inhibitor is non-flammable liquid. Use in well ventilated area. Keep container tightly closed when not in use. Wear appropriate PPE.

PACKAGING
Packaging in 200 liters drum.

2” System Coupon Holder is a mounting for corrosion coupon and scale coupon.
Solutions for the prevention and control of corrosion, variety of coupon support styles of coupon type. Below variety of coupon holder model.

  1. Strip Coupon Holder: Use to corrosion coupons or scale coupon type 3 “or 6” length, the length of holder base on the area position to monitor, top, middle or bottom.
  2. Adjustable Disc Coupon Holder: Use for monitoring flush with pipe commonly for pinging line, the length we can adjusted as flush of internal pipe .
  3. Fixed Disc Coupon Holder: Use for disc coupon with fixed monitoring poin
  4. Multiple Disc Coupon Holder: Use for disc coupon with monitoring top, middle and bottom pararel or simultan. Available for pipes with diameters of 6 “or more.
  5. Ladder Strip Coupon Holder : Use for strip coupon with monitoring top, middle and bottom pararel or simultan. Available for pipe with diameters of 6 “or more.

Retractable unit coupon insertion system commonly used in field and plants applications. A specially designed packaging gland is used to insert or retract a coupon from a pressure-stopped pressure system.

Retractable Specifications:

Std. Length 18″
24″
30″
36″
Material 316L SS
Temperature Rating 360° C
Pressure Rating 1500 PSI / 103.4 Bar
Mounting 1″ Full Port Valve (min.)
Standard Meets NACE MR0175 and MR0103
Reference Catalog Bcormon

Double Block Services Valve installed on top of a mechanical or hydraulic access fitting and provides temporary containment and control of pipeline media, as well as the mounting point for the mechanical retriever tool during installation/retrieval of monitoring devices such as corrosion coupon, corrosion probe, etc.

This tool also allows equitable control of the pressure between the side of the pipe and the side of the retriever. There are have needle valve for the lower ball and seat assemblies. Evenly distributed pressure reduces the torque needed to operate the valve.

It also reduces pressure from fast pressurization, thus extending the lives of the seats, o-ring and components of valve. A blinking cap/plug assembly can be installed on the valve as an additional safety measure, if the plug cannot be removed, or if a longer term sealing is required. However, the services valve is not designed to be mounted permanently.

This tool is manufactured from stainless steel 316 SS for 6000 psi, Carbon Steel for 3600 psi and 2500 psi. Material meet with NACE MR0175. The weight of the Valve is approximately 50.7 lbs (23 kg), standard temperature up to 204 degree celsius .
The services valve comes as a box and includes a non-spark hammer, an extension bar and a tools kit.

Pressure Rating 3600 PSI (24.8 Mpa)
Seal Options Available for Temperature Rating up to +450 °F (+232 °C)
Compatible All Retrievers
Material 316L / SS, A105 CS
Standard Meets NACE MR0175 and MR0103
Safe Pressurization with By-Pass Bleed Valve Provides
Type Double Service Valve

Flush disc coupon of various sizes and models for 2″ system corrosion monitoring, which are commonly used for oil and gas, upstream dan downstream, chemical companies, etc. Generally used in applications where the coupon cannot extend into the pipe to interfere with the flow or pigging operations.

Specifications:

Material AISI 1018, ASTM A106 gr B, or others
Weight Below 50 gram union depend on the model, details will be listed on the envelope
Standard NACE RP-0775 and ASTM G-1
Dimension OD:1.25″, Thickness 1/8″
Other Type Multiple Disc Coupon Monitoring is available for pipes with diameters of 6″ or more
Refer Catalog Bcormon

Showing 1–12 of 26 results